Standard Precautions are  infection prevention practices that apply to all patient care, regardless of suspected or confirmed infection status of the patient, in any setting where health care is delivered. These practices are designed to both protect DHCP (dental health-care personnel ) and prevent DHCP from spreading infections among patients. Standard Precautions include —

1. Hand hygiene.

2. Use of personal protective equipment (e.g., gloves, masks, eyewear).

3. Respiratory hygiene / cough etiquette.

4. Sharps safety (engineering and work practice controls).
5. Safe injection practices (i.e., aseptic technique for parenteral medications).
6. Sterile instruments and devices.
7. Clean and disinfected environmental surfaces.

Each element of Standard Precautions is described in the following sections. Education and training are critical elements of Standard Precautions, because they help DHCP make appropriate decisions and comply with recommended practices.

When Standard Precautions alone cannot prevent transmission, they are supplemented with Transmission-Based Precautions. This second tier of infection prevention is used when patients have diseases that can spread through contact, droplet or airborne routes (e.g., skin contact, sneezing, coughing) and are always used in addition to Standard Precautions. Dental settings are not typically designed to carry out all of the Transmission-Based Precautions (e.g., Airborne Precautions for patients with suspected tuberculosis, measles, or chickenpox) that are recommended for hospital and other ambulatory care settings. Patients, however, do not usually seek routine dental outpatient care when acutely ill with diseases requiring Transmission-Based Precautions. Nonetheless, DHCP should develop and carry out systems for early detection and management of potentially infectious patients at initial points of entry to the dental setting. To the extent possible, this includes rescheduling non-urgent dental care until the patient is no longer infectious or referral to a dental setting with appropriate infection prevention precautions when urgent dental treatment is needed.

Hand Hygiene

Hand hygiene is the most important measure to prevent the spread of infections among patients and DHCP. Education and training programs should thoroughly address indications and techniques for hand hygiene practices before performing routine and oral surgical procedures.

For routine dental examinations and nonsurgical procedures, use water and plain soap (hand washing) or antimicrobial soap (hand antisepsis) specific for health care settings or use an alcohol-based hand rub. Although alcohol-based hand rubs are effective for hand hygiene in health care settings, soap and water should be used when hands are visibly soiled (e.g., dirt, blood, body fluids). For surgical procedures,¹ perform a surgical hand scrub before putting on sterile surgeon’s gloves. For all types of hand hygiene products, follow the product manufacturer’s label for instructions. Complete guidance on how and when hand hygiene should be performed, including recommendations regarding surgical hand antisepsis and artificial nails can be found in the Guideline for Hand Hygiene in Health-Care Settings pdf icon[PDF – 494 KB].

Footnote

¹ Definition from 2003 CDC Dental Guidelines—Oral surgical procedures involve the incision, excision, or reflection of tissue that exposes the normally sterile areas of the oral cavity. Examples include biopsy, periodontal surgery, apical surgery, implant surgery, and surgical extractions of teeth (e.g., removal of erupted or nonerupted tooth requiring elevation of mucoperiosteal flap, removal of bone or section of tooth, and suturing if needed).

Personal Protective Equipment

Personal protective equipment (PPE) refers to wearable equipment that is designed to protect DHCP from exposure to or contact with infectious agents. PPE that is appropriate for various types of patient interactions and effectively covers personal clothing and skin likely to be soiled with blood, saliva, or other potentially infectious materials (OPIM) should be available. These include gloves, face masks, protective eye wear, face shields, and protective clothing (e.g., reusable or disposable gown, jacket, laboratory coat). Examples of appropriate use of PPE for adherence to Standard Precautions include—

• Use of gloves in situations involving possible contact with blood or body fluids, mucous membranes, non-intact skin (e.g., exposed skin that is chapped, abraded, or with dermatitis) or OPIM.
• Use of protective clothing to protect skin and clothing during procedures or activities where contact with blood or body fluids is anticipated.
• Use of mouth, nose, and eye protection during procedures that are likely to generate splashes or sprays of blood or other body fluids.

DHCP should be trained to select and put on appropriate PPE and remove PPE so that the chance for skin or clothing contamination is reduced. Hand hygiene is always the final step after removing and disposing of PPE. Training should also stress preventing further spread of contamination while wearing PPE by:

• Keeping hands away from face.
• Limiting surfaces touched.
• Removing PPE when leaving work areas.
• Performing hand hygiene.

The application of Standard Precautions and guidance on appropriate selection and an example of putting on and removal of personal protective equipment is described in detail in the 2007 Guideline for Isolation Precautions pdf icon[PDF – 1.4 MB].

Respiratory Hygiene/Cough Etiquette

Respiratory hygiene/cough etiquette infection prevention measures are designed to limit the transmission of respiratory pathogens spread by droplet or airborne routes. The strategies target primarily patients and individuals accompanying patients to the dental setting who might have undiagnosed transmissible respiratory infections, but also apply to anyone (including DHCP) with signs of illness including cough, congestion, runny nose, or increased production of respiratory secretions.

DHCP should be educated on preventing the spread of respiratory pathogens when in contact with symptomatic persons. Respiratory hygiene/cough etiquette measures were added to Standard Precautions in 2007. Additional information related to respiratory hygiene/cough etiquette can be found in the 2007 Guideline for Isolation Precautions pdf icon[PDF – 1.4 MB]  Recommendations for preventing the spread of influenza are available at: https://www.cdc.gov/flu/professionals/infectioncontrol/.

Sharps Safety

Most percutaneous injuries (e.g., needlestick, cut with a sharp object) among DHCP involve burs, needles, and other sharp instruments. Implementation of the OSHA Bloodborne Pathogens Standard has helped to protect DHCP from blood exposure and sharps injuries. However, sharps injuries continue to occur and pose the risk of bloodborne pathogen transmission to DHCP and patients. Most exposures in dentistry are preventable; therefore, each dental practice should have policies and procedures available addressing sharps safety. DHCP should be aware of the risk of injury whenever sharps are exposed. When using or working around sharp devices, DHCP should take precautions while using sharps, during cleanup, and during disposal.

Engineering and work-practice controls are the primary methods to reduce exposures to blood and OPIM from sharp instruments and needles. Whenever possible, engineering controls should be used as the primary method to reduce exposures to bloodborne pathogens. Engineering controls remove or isolate a hazard in the workplace and are frequently technology-based (e.g., self-sheathing anesthetic needles, safety scalpels, and needleless IV ports). Employers should involve those DHCP who are directly responsible for patient care (e.g., dentists, hygienists, dental assistants) in identifying, evaluating and selecting devices with engineered safety features at least annually and as they become available. Other examples of engineering controls include sharps containers and needle recapping devices.

When engineering controls are not available or appropriate, work-practice controls should be used. Work-practice controls are behavior-based and are intended to reduce the risk of blood exposure by changing the way DHCP perform tasks, such as using a one-handed scoop technique for recapping needles between uses and before disposal. Other work-practice controls include not bending or breaking needles before disposal, not passing a syringe with an unsheathed needle by hand, removing burs before disassembling the handpiece from the dental unit, and using instruments in place of fingers for tissue retraction or palpation during suturing and administration of anesthesia.

All used disposable syringes and needles, scalpel blades, and other sharp items should be placed in appropriate puncture-resistant containers located close to the area where they are used. Sharps containers should be disposed of according to state and local regulated medical waste rules.

For more information about sharps safety, see the Guidelines for Infection Control in Dental Health-Care Settings—2003 pdf icon[PDF – 1.21 MB], the CDC Workbook for Designing, Implementing, and Evaluating a Sharps Injury Prevention Program, and the CDC Sample Screening and Device Evaluation Forms for Dentistry.

Safe Injection Practices

Safe injection practices are intended to prevent transmission of infectious diseases between one patient and another, or between a patient and DHCP during preparation and  administration of parenteral (e.g., intravenous or intramuscular injection) medications. Safe injection practices are a set of measures DHCP should follow to perform injections in the safest possible manner for the protection of patients. DHCP most frequently handle parenteral medications when administering local anesthesia, during which needles and cartridges containing local anesthetics are used for one patient only and the dental cartridge syringe is cleaned and heat sterilized between patients. Other safe practices described here primarily apply to use of parenteral medications combined with fluid infusion systems, such as for patients undergoing conscious sedation. Unsafe practices that have led to patient harm include 1) use of a single syringe — with or without the same needle — to administer medication to multiple patients, 2) reinsertion of a used syringe — with or without the same needle — into a medication vial or solution container (e.g., saline bag) to obtain additional medication for a single patient and thenusing that vial or solution container for subsequent patients, and 3) preparation of medications in close proximity to contaminated supplies or equipment.

Safe injection practices were covered in the Special Considerations section (Aseptic Technique for Parenteral Medications) of the 2003 CDC dental guidelines. However, because of reports of transmission of infectious diseases by inappropriate handling of injectable medications, CDC now considers safe injection practices to be a formal element of Standard Precautions. Complete guidance on safe injection practices can be found in the 2007 Guideline for Isolation Precautions pdf icon[PDF – 1.4 MB]. Additional materials, including a list of frequently asked questions from providers and a patient notification toolkit, are also available. The One & Only Campaign is a public health effort to eliminate unsafe medical injections. The campaign is led by CDC and the Safe Injection Practices Coalition (SIPC). To learn more about safe injection practices and access training videos and resources, please visit
http://www.oneandonlycampaign.org/external icon.

Footnotes

² A technique that prevents or reduces the spread of microorganisms from one site to another, such as from patient to DHCP, from patient to operatory surfaces, or from one operatory surface to another.

* A Note about Administering Local Dental Anesthesia: When using a dental cartridge syringe to administer local anesthesia, do not use the needle or anesthetic cartridge for more than one patient. Ensure that the dental cartridge syringe is appropriately cleaned and heat sterilized before use on another patient.

Sterilization and Disinfection of Patient-Care Items and Devices

Instrument processing requires multiple steps using specialized equipment. Each dental practice should have policies and procedures in place for containing, transporting, and handling instruments and equipment that may be contaminated with blood or body fluids. Manufacturer’s instructions for reprocessing reusable dental instruments and equipment should be readily available—ideally in or near the reprocessing area. Most single-use devices are labeled by the manufacturer for only a single use and do not have reprocessing instructions. Use single-use devices for one patient only and dispose of appropriately.

Cleaning, disinfection and sterilization of dental equipment should be assigned to DHCP with training in the required reprocessing steps to ensure reprocessing results in a device that can be safely used for patient care. Training should also include the appropriate use of PPE necessary for safe handling of contaminated equipment.
Patient-care items (e.g., dental instruments, devices, and equipment) are categorized as critical, semicritical, or noncritical, depending on the potential risk for infection associated with their intended use.

• Critical items, such as surgical instruments and periodontal scalers, are those used to penetrate soft tissue or bone. They have the greatest risk of transmitting infection and should always be sterilized using heat.
• Semicritical items (e.g., mouth mirrors, amalgam condensers, reusable dental impression trays) are those that come in contact with mucous membranes or non-intact skin (e.g., exposed skin that is chapped, abraded, or has dermatitis). These items have a lower risk of transmission. Because the majority of semicritical items in dentistry are heat-tolerant, they should also be sterilized using heat. If a semicritical item is heat-sensitive, DHCP should replace it with a heat-tolerant or disposable alternative. If none are available, it should, at a minimum, be processed using high-level disinfection.

Note: Dental handpieces and associated attachments, including low-speed motors and reusable prophylaxis angles, should always be heat sterilized between patients and not high-level or surface disinfected. Although these devices are considered semicritical, studies have shown that their internal surfaces can become contaminated with patient materials during use. If these devices are not properly cleaned and heat sterilized, the next patient may be exposed to potentially infectious materials.

Digital radiography sensors are also considered semicritical and should be protected with a Food and Drug Administration (FDA)-cleared barrier to reduce contamination during use, followed by cleaning and heat-sterilization or high-level disinfection between patients. If the item cannot tolerate these procedures then, at a minimum, protect with an FDA-cleared barrier. In addition, clean and disinfect with an Environmental Protection Agency (EPA)-registered hospital disinfectant with intermediate-level (i.e., tuberculocidal claim) activity between patients. Because these items vary by manufacturer and their ability to be sterilized or high-level disinfected also vary, refer to manufacturer instructions for reprocessing.

• Noncritical patient-care items (e.g., radiograph head/cone, blood pressure cuff, facebow) are those that only contact intact skin. These items pose the least risk of transmission of infection. In the majority of cases, cleaning, or if visibly soiled, cleaning followed by disinfection with an EPA-registered hospital disinfectant is adequate. Protecting these surfaces with disposable barriers might be a preferred alternative.

Cleaning to remove debris and organic contamination from instruments should always occur before disinfection or sterilization. If blood, saliva, and other contamination are not removed, these materials can shield microorganisms and potentially compromise the disinfection or sterilization process. Automated cleaning equipment (e.g., ultrasonic cleaner, washer-disinfector) should be used to remove debris to improve cleaning effectiveness and decrease worker exposure to blood. After cleaning, dried instruments should be inspected, wrapped, packaged, or placed into container systems before heat sterilization. Packages should be labeled to show the sterilizer used, the cycle or load number, the date of sterilization, and, if applicable, the expiration date. This information can help in retrieving processed items in the event of an instrument processing/sterilization failure.

The ability of a sterilizer to reach conditions necessary to achieve sterilization should be monitored using a combination of biological, mechanical, and chemical indicators. Biological indicators, or spore tests, are the most accepted method for monitoring the sterilization process because they assess the sterilization process directly by killing known highly resistant microorganisms (e.g., Geobacillus or Bacillus species). A spore test should be used at least weekly to monitor sterilizers. However, because spore tests are only performed periodically (e.g., once a week, once a day) and the results are usually not obtained immediately, mechanical and chemical monitoring should also be performed.

Mechanical and chemical indicators do not guarantee sterilization; however, they help detect procedural errors and equipment malfunctions. Mechanical monitoring involves checking the sterilizer gauges, computer displays, or printouts; and documenting the sterilization pressure, temperature, and exposure time in your sterilization records. Since these parameters can be observed during the sterilization cycle, this might be the first indication of a problem.

Chemical monitoring uses sensitive chemicals that change color when exposed to high temperatures or combinations of time and temperature. Examples include chemical indicator tapes, strips or tabs, and special markings on packaging materials. Chemical monitoring results are obtained immediately following the sterilization cycle and therefore can provide more timely information about the sterilization cycle than a spore test. A chemical indicator should be used inside every package to verify that the sterilizing agent (e.g., steam) has penetrated the package and reached the instruments inside. If the internal chemical indicator is not visible from the outside of the package, an external indicator should also be used. External indicators can be inspected immediately when removing packages from the sterilizer. If the appropriate color change did not occur, do not use the instruments. Chemical indicators also help to differentiate between processed and unprocessed items, eliminating the possibility of using instruments that have not been sterilized.

Note: A single-parameter internal chemical indicator provides information regarding only one sterilization parameter (e.g., time or temperature). Multiparameter internal chemical indicators are designed to react to ≥ 2 parameters (e.g., time and temperature; or time, temperature, and the presence of steam) and can provide a more reliable indication that sterilization conditions have been met.

Sterilization monitoring (e.g., biological, mechanical, chemical monitoring) and equipment maintenance records are an important component of a dental infection prevention program. Maintaining accurate records ensures cycle parameters have been met and establishes accountability. In addition, if there is a problem with a sterilizer (e.g., unchanged chemical indicator, positive spore test), documentation helps to determine if an instrument recall is necessary.

Ideally, sterile instruments and supplies should be stored in covered or closed cabinets. Wrapped packages of sterilized instruments should be inspected before opening and use to ensure the packaging material has not been compromised (e.g., wet, torn, punctured) during storage. The contents of any compromised packs should be reprocessed (i.e., cleaned, packaged, and heat-sterilized again) before use on a patient.

Recommendations for the cleaning, disinfection, and sterilization of dental equipment can be found in the Guidelines for Infection Control in Dental Health-Care Settings—2003 pdf icon[PDF – 1.21 MB]. Recommendations for the cleaning, disinfection, and sterilization of medical equipment are available in the Guideline for Disinfection and Sterilization in Healthcare Facilities pdf icon[PDF – 1 MB] (available at: www.cdc.gov/infectioncontrol/pdf/guidelines/disinfection-guidelines.pdf pdf icon[PDF – 1 MB]). FDA regulations on reprocessing of single-use devices are available at: https://www.fda.gov/downloads/MedicalDevices/DeviceRegulationandGuidance/GuidanceDocuments/ucm071441.pdf pdf icon[PDF – 554 KB]external icon.

Environmental Infection Prevention and Control

Policies and procedures for routine cleaning and disinfection of environmental surfaces should be included as part of the infection prevention plan. Cleaning removes large numbers of microorganisms from surfaces and should always precede disinfection. Disinfection is generally a less lethal process of microbial inactivation (compared with sterilization) that eliminates virtually all recognized pathogenic microorganisms but not necessarily all microbial forms (e.g., bacterial spores).

Emphasis for cleaning and disinfection should be placed on surfaces that are most likely to become contaminated with pathogens, including clinical contact surfaces (e.g., frequently touched surfaces such as light handles, bracket trays, switches on dental units, computer equipment) in the patient-care area. When these surfaces are touched, microorganisms can be transferred to other surfaces, instruments or to the nose, mouth, or eyes of DHCP or patients. Although hand hygiene is the key to minimizing the spread of microorganisms, clinical contact surfaces should be barrier protected or cleaned and disinfected between patients. EPA-registered hospital disinfectants or detergents / disinfectants with label claims for use in health care settings should be used for disinfection. Disinfectant products should not be used as cleaners unless the label indicates the product is suitable for such use. DHCP should follow manufacturer recommendations for use of products selected for cleaning and disinfection (e.g., amount, dilution, contact time, safe use, and disposal). Facility policies and procedures should also address prompt and appropriate cleaning and decontamination of spills of blood or other potentially infectious materials. Housekeeping surfaces, (e.g., floors, walls, sinks) carry less risk of disease transmission than clinical contact surfaces and can be cleaned with soap and water or cleaned and disinfected if visibly contaminated with blood.

Additional guidance for the cleaning and disinfection of environmental surfaces—including for cleaning blood or body substance spills—is available in the Guidelines for Environmental Infection Control in Health-Care Facilities pdf icon[PDF – 1 MB] and the Guideline for Disinfection and Sterilization in Healthcare Facilities pdf icon[PDF – 1 MB].